#Spinning

2025-01-29

Rieter reports a strong increase in order intake for the 2024 financial year, with a sharp decline in sales

At CHF 725.5 million, order intake was significantly higher than in the same period of the previous year (2023: CHF 541.8 million), representing an increase of 34%. This was the fourth consecutive quarter of year-on-year growth. As expected, the Rieter Group ended financial year 2024 with lower sales than in the previous year. According to preliminary, unaudited figures, total sales amounted to CHF 859.1 million, which is around 39% down on the previous year (2023: CHF 1 418.6 million).

For the full year 2024, Rieter expects an EBIT margin in the upper half of the guidance range of 2% to 4% communicated in October 2024 (2023: 7.2%).

Order intake

Order intake in 2024 was 34% higher than in the previous year at CHF 725.5 million (2023: CHF 541.8 million). Rieter thus succeeded in strengthening its competitive position in a challenging market environment. Compared with the previous year, there were signs of an initial market recovery.

Sales by division

The Machines & Systems Division posted sales of CHF 424.9 million, a decrease of 56% compared with the previous year (2023: CHF 965.0 million). In the Components Division, sales declined to CHF 247.6 million, down 7% from the same period of the previous year (2023: CHF 266.2 million). The After Sales Division reported sales of CHF 186.6 million, comparable to the previous year (2023: CHF 187.4 million).

Order backlog

At the end of 2024, the company had an order backlog of about CHF 530 million (December 31, 2023: CHF 650 million).

EBIT margin

Rieter successfully implemented the measures of the “Next Level” performance program. Despite significantly lower sales, a solid EBIT margin is expected in the upper half of the 2% to 4% guidance range, as communicated in October 2024.

Results Press Conference 2025

Rieter will provide further details on the financial year on March 13, 2025. The Group will also publish its Annual Report 2024 and hold an annual results press conference.

Annual General Meeting of April 24, 2025

The next Annual General Meeting of Rieter Holding Ltd. will take place on Wednesday, April 24, 2025. Proposals regarding the agenda must be submitted in writing to Rieter Holding Ltd., Office of the Company Secretary, Klosterstrasse 20, CH-8406 Winterthur (Switzerland) by no later than February 28, 2025, accompanied by information concerning the relevant motions and evidence of the necessary shareholdings (with a par value of CHF 0.5 million as stipulated by §9 of the Articles of Association).

Rieter adjusts group structure in preparation for Barmag integration

The planned acquisition of the “Barmag” Division of OC Oerlikon will create the leading system provider worldwide for natural and man-made fibers. Rieter is confident it will receive all regulatory approvals to complete the acquisition in the fourth quarter of 2025. The Rieter Group is therefore adjusting its Group structure as of January 1, 2026, to take this acquisition into account and to be able to provide an even more agile response to market challenges.

Rieter reports stable order backlog and strategic progress – outlook for 2025 adjusted

In its Investor Update 2025, Rieter announced an order intake of CHF 203.9 million in the third quarter and CHF 559.3 million after nine months, reflecting a continued cautious investment climate in the textile machinery sector. Sales totaled CHF 121.5 million in the third quarter and CHF 457.7 million for the first nine months of the year, while the order backlog stood at around CHF 590 million as of September 30, 2025.

FET prepares for final exhibition of 2025

Fibre Extrusion Technology Ltd (FET) of Leeds, UK has completed its second major exhibition of 2025 at ITMA ASIA in Singapore, which is aimed at the textile and garment industry in South and Southeast Asia and the Middle East. Once again, this trade show proved to be a successful one for FET, with considerable interest from several countries surrounding China.

T-CAN – Revolutionizing can transport

In virtually all spinning mills, transporting sliver cans is still done manually. Rising labor costs, lack of operators and increasing quality requirements make this a growing challenge. With T-CAN, Trützschler introduces a practical solution: a fully automated can transport system that will be presented live at ITMA ASIA 2025 in Singapore.

textile.4U publishes special edition “Top 100 Textile Recycling Companies 2025”

With a comprehensive 176-page special edition, textile.4U is dedicating its latest issue entirely to one of the most dynamic and influential topics in today’s textile industry: textile recycling. The new issue, published exclusively in high-quality print, presents the Top 100 textile recycling companies researched and selected by TexData – organizations that already play a key role in the transition to circular textiles or are expected to have a significant impact in the near future.

Navis TubeTex announces U.S. partnership with Icomatex

Navis TubeTex, a global leader in advanced dyeing and finishing machinery solutions, is pleased to announce a new partnership with Icomatex (www.icomatex.com), a respected European manufacturer of high-quality stenters and textile finishing equipment. Under this agreement, Navis TubeTex will exclusively represent the Icomatex stenter line in the United States.

ADVANSA launches ADVA®tex: A new step toward textile-to-textile recycling

ADVANSA has introduced ADVA®tex, a new filling fibre made entirely from recycled pre-consumer textile waste, positioning the material as a significant step forward in textile-to-textile (T2T) recycling. The fibre is designed for use in duvets, pillows, mattresses, and furniture applications and is available in three versions.

KARL MAYER celebrates 35 years of EL pattern drive

KARL MAYER is celebrating an anniversary this year: on 30 November 1990, the first warp knitting machine with electronic guide bar control, the KS 4 EL, was delivered – another milestone for patterning. As early as 1980, the SU gearbox with the MRS42SU had initiated the transition from mechanical chains to digital data.